For the fastest time-to-market of your products, we provide a number of rapid prototyping DSP subsystems (TMS320DM64x, TMS320VC33, Blackfin, and other platforms), custom designed OEM Boards for special applications, FPGA integration and the best of support from component selection to production. Here are some hardware product we can offer to support your design (selection only, please enquire for availability). All products can be customized for use in proprietary systems, even at small quantities. Embedded products are offered through A.R. Bayer DSP Systeme GmbH and our distribution partners.
This little controller board is based on a Blackfin BF537 DSP controller and a Spartan3E FPGA. It is capable of running uClinux, has 32MBytes on-board SDRAM, 16 MBytes of serial flash, up to 33 I/O pins, a 100Mbps Ethernet port with on-board PHY and lots of applications to be used in.
If you wish to learn more about this nice little piece of engineering, check the datasheet or contact us. We not only provide you with the hardware but also with engineering support to make your application real - quickly!
Multi-Core Blackfin module with up to 5300MIPS
A single BF537 with an Ethernet MAC, capable of running uClinux, controls four dual-core BF561’s producing an accumulated performance of up to 5300 MIPS. With a size of only 1" x 3.75", the board is designed to fit standard carrier boards, such as PCI, PCIx or eurocards (160x100mm).
The BF537 is clocked at 500MHz and has 32 Mbytes private SDRAM (125 MHz) to suit the requirements of an operating system (uClinux) while each BF561 has 8 Mbytes of private SDRAM (133 MHz). The board can boot via TFTP over the network and load application software individually to each of the BF561 cores. Alternatively, the board can be booted from an on-board serial flash which makes it independent of any host system.
A single 3 Volt 2 Amps rail is required, where the supply voltage also determines the I/O voltage.
For more information you may contact us or have a look at the datasheet.
DSP Module w/ TMS320DM642 & 200K Spartan3 FPGA for Video Applications
This DSP Module is the most powerful sub-system in our standard footprint range of products. Based on a DM642 multimedia DSP from Texas Instruments clocked at up to 600 MHz, accompanied by a Xilinx Spartan3-FPGA, this hardware provides all the flexibility and computational power required in multi media processing , especially in image and video compression.
Many I/O ports are available at the connectors, many of which are capable of the LVDS standard. A version for the extended temperature range is available on request.
Please, check the datasheet or contact us for more information.
This DSP Module is flexible sub-system in our standard footprint range of products, based on a BF532 or BF533 Blackfin processor from Analog Devices clocked at 400/600/756MHz respectively. It comes equipped with a CPLD for flexible I/O handling and a 2-channel audio codec for speech applications. SDRAM of up to 16 MByte is optional. More details are found in the datasheet or you may contact us for more information.
PC81 PCI Board with ADI 33 MHz ADSP-2181 Processor and 2-channel AC97 audio interface, general purpose I/O, 1 MByte flash and watchdog timer. Comes with drivers for Win98, Win 2k and XP. Suitable for PC-embedded VoIP solutions and other voice related applications. Note: This is a legacy product which may not be on stock. You may still request more information or take a look at the datasheet.
DSP Controller Board w/ Texas Instruments TMS320VC33
This module named "VC33modU" comes with a 2-channel UART, a low-power CPLD, 2 MByte low-power SRAM and 2 MByte flash ROM. It is based on a 60/75 MIPS TI TMS320VC33 Floating Point DSP and has a customer programmable Host/GPIO interface implemented in a 128 macrocell Coolrunner CPLD.
Datasheet (PDF)
DSP Module w/ Blackfin BF532/533 for Audio Applications